|
R400 RUBBER APPLICATION PROCEDURE:
1. Thoroughly clean the surface
by high pressure water and or detergent to remove any film, scale, loose material, oils or foreign material that will inhibit
bonding.
2. Apply SEALER 200 to the entire surface. The sealer is used to insure adhesion in that the R400 will adhere to the substrate. Do not thin or dilute
this product. The sealer should be sprayed or rolled as a continuous unbroken film or coat.
3. R400 RUBBER FIBERED PUTTY GRADE is to be applied
to all cracks and corners.
4. At all expansion joints, the
stitchbond W201 needs to be relieved in whatever manner desired so that the relief or slack is greater than the movement of
the expansion joint. Generally backing rod is used to create the slack.
5. Apply R400 RUBBER to the prepared surface by brush, roller
or spray. Do not thin or dilute this product.
Apply one complete coat after 1st coat dries minimum 1 to
4 hours, apply the Stitchbond W201 to the surface using a coat of R400 over the stitchbond
to secure it to the 1st coat of R400 RUBBER. Allow to dry.
6. Apply multi-coats of R400 RUBBER until the strings in the stitchbond are no longer visible. Which should be a total of all coats, under and over the stitchbond of 35-40 dry mils. There shall be no air pockets under the fabric with exception of the expansion joints. The fabric should lay flat on the surface and there shall be no pinholes, folds or protrusions to interrupt the continuous
film.
7. No top
coat is needed with R400 RUBBER. Precautions must be made to not damn water.
Water must be diverted on to and not under the waterproofing coating.
GALLONS REQUIRED FOR PROPER COATING THICKNESS
When using the Stitchbond fabric, for every 100 to 150 square feet of deck,
one 5 (five) gallon can of R400 Rubber must be used.
8. Deck pavers,
indoor outdoor carpeting, R400
RUBBER deck rock, or silica sand mixture may be applied over the R400 Rubber to construct a walking surface. When applying
deck pavers, the sand is placed over the R400 Rubber and the pavers are set as they normally would be over concrete.
R400 RUBBER APPLICATION PROCEDURE:
1. Thoroughly clean the surface
by high pressure water and or detergent to remove any film, scale, loose material, oils or foreign material that will inhibit
bonding.
2. Apply SEALER 200 to the entire surface. The sealer is used to insure adhesion in that the R400 will adhere to the substrate. Do not thin or dilute
this product. The sealer should be sprayed or rolled as a continuous unbroken film or coat.
3. R400 RUBBER FIBERED PUTTY GRADE is to be applied
to all cracks and corners.
4. At all expansion joints, the
stitchbond W201 needs to be relieved in whatever manner desired so that the relief or slack is greater than the movement of
the expansion joint. Generally backing rod is used to create the slack.
5. Apply R400 RUBBER to the prepared surface by brush, roller
or spray. Do not thin or dilute this product.
Apply one complete coat after 1st coat dries minimum 1 to
4 hours, apply the Stitchbond W201 to the surface using a coat of R400 over the stitchbond
to secure it to the 1st coat of R400 RUBBER. Allow to dry.
6. Apply multi-coats of R400 RUBBER until the strings in the stitchbond are no longer visible. Which should be a total of all coats, under and over the stitchbond of 35-40 dry mils. There shall be no air pockets under the fabric with exception of the expansion joints. The fabric should lay flat on the surface and there shall be no pinholes, folds or protrusions to interrupt the continuous
film.
7. No top
coat is needed with R400 RUBBER. Precautions must be made to not damn water.
Water must be diverted on to and not under the waterproofing coating.
GALLONS REQUIRED FOR PROPER COATING THICKNESS
When using the Stitchbond fabric, for every 100 to 150 square feet of deck,
one 5 (five) gallon can of R400 Rubber must be used.
8. Deck pavers,
indoor outdoor carpeting, R400
RUBBER deck rock, or silica sand mixture may be applied over the R400 Rubber to construct a walking surface. When applying
deck pavers, the sand is placed over the R400 Rubber and the pavers are set as they normally would be over concrete.
FLAT ROOF WITH PONDING WATER R400RUBBER
APPLICATION PROCEDURE:
1. Thoroughly clean the surface by high pressure water and or detergent to remove any film, scale, loose material, oils or foreign material that will inhibit bonding.
2. The Sub-straite should be clean and stable, Cement Slurry may be used to fill in cracks, voids and loose material ie: Gravel. This will smooth the surface and achieve a clean dry stable sub-straite, to be waterproof.
3. Apply SEALER 200 to the entire surface. The sealer is used to insure adhesion and stop chalking. Do not thin or dilute this product. The sealer should be sprayed or rolled as a continuous unbroken film or coat.SEALER 200 Dries tacky in 30 Min.
4. R400 RUBBER FIBERED PUTTY GRADE is to be applied to all cracks and corners.
5. At all expansion joints, stitchbond W 201 Fabric is to be used and needs to be relieved so that the relief or slack is greater than the movement of the expansion joint. Generally backing rod is used to create the slack.
6. Apply R400 RUBBER to the prepared surface by brush, roller or spray. Do not thin or dilute this product. Apply one complete coat after 1st coat dries minimum 1 to 4 hours, apply the Stitchbond W201 to the surface using a coat of R400 over the stitchbond to secure fabric to the 1st coat of R400 RUBBER.
7. Apply multi-coats of R400 RUBBER until the strings in the stitchbond are no longer visible. Which should be a total of all coats, under and over the stitchbond of 35-40 dry mils. There shall be no air pockets under the fabric with exception of the expansion joints. The fabric should lay flat on the surface and there shall be no pinholes, folds or protrusions to interrupt the continuous film.
8. No top coat is needed with R400 RUBBER. Precautions must be made to not damn water. Water must be diverted on to and not under the waterproofing coating.
GALLONS REQUIRED FOR PROPER COATING THICKNESS
When using the Stitchbond fabric, for every 100 to 150 square feet of deck, one 5 (five) gallon can of R400 Rubber must be used.
9. Deck pavers, indoor outdoor carpeting, R400 RUBBER deck rock, or silica sand mixture may be applied over the R400 Rubber to construct a walking surface. When applying deck pavers, the sand is placed over the R400 Rubber and the pavers are set as they normally would be over concrete.